Need Help with Berry's Bullets 9mm 124 Load Data

Ammunition & Reloading
1

I’ve been diving into reloading my own 9mm ammunition, and I’m particularly interested in sourcing accurate load data for Berry’s 9mm 124 grain bullets. I’ve heard some talk about these bullets being a solid choice for both range training and self-defense, but I’m looking for some clarity on the specifics.

What I’m Looking For

  • Powder Recommendations: Which powders have proven to work best with these bullets? I’ve read about a few, but I’d love to hear what the community uses.
  • Load Specifications: Ideally, I’d want to know the recommended charge weights for various powders. What are you all loading for target shooting versus defensive scenarios?
  • Seating Depths: Any tips on bullet seating depth? I want to ensure my loads are feeding smoothly in my pistol.

Experiences to Share

If you’ve had any experiences—good or bad—with Berry’s 9mm 124 bullets, I’d love to hear them. Did you encounter any issues, or were the loads consistent? I’m interested in any tips you may have to make the reloading process as safe and effective as possible.

Conclusion

I’m eager to get started and would appreciate any insights, data, or personal experiences you might want to share. Thanks in advance for your help!

2

I’ve been loading Berry’s 9mm 124 grain with 4.0 to 4.5 grains of Bullseye powder. It consistently produces tight groups at the range. Overall length (OAL) for my loads is 1.135". Give it a try!

3

That sounds great! I’ve also had success with 4.2 grains of Titegroup. My OAL is around 1.125". Both powders seem to perform well in my experience!

5 Likes
4

For those using Berry’s 124 grain bullets, Winchester 231 is another solid choice. I typically use 4.3 grains and set my OAL at 1.130". Super reliable!

4 Likes
5

I agree with you on that! But I find that a higher charge weight around 4.5 grains gives me less recoil for follow-up shots!

6

Titegroup is a fun powder to play with! Just remember, it can be a little finicky with the charge weight. I tend to stick to about 4.0 to 4.4 grains for safety.

7

If you’re going for maximum performance with Berry’s, consider trying Nitro 100. I’ve achieved great results with an OAL of 1.142". Has anyone here used that powder?

8

I haven’t tried Nitro 100 yet, but I’m intrigued! What charge weight are you using?

9

Honestly, I prefer to stick to a safe zone with my loads. I’m usually around 4.0 to 4.2 grains for everything. No rush, just reliable performance!

10

Safe is definitely better, especially for those new to reloading! How long have you been doing this?

3 Likes
11

I’ve been reloading for over 5 years now, but I still tread carefully! Safety is key. I usually load my own OAL for each session based on accuracy tests.

12

My first attempt went south – had some keyholing issues. Turns out, I was too long on my OAL. Lesson learned: always check!

3 Likes
13

Ouch! Keyholing can be a real pain! Glad you figured it out. I was skeptical about Berry’s until I tried them; they’re surprisingly good!

14

You shouldn’t have to stress about your rounds too much. Whether it’s Berry’s or another brand, what matters is the quality of your components and attention to detail. Have fun with it!

15

Much agreed! But hey, if something breaks out, always blame the powder… right? Just kidding!

16

Totally! There is something fun about blaming the powder. But let’s make sure we’re all reloading safely. I enjoy trying out different loads for different scenarios.

17

It’s all part of the journey! Just remember: a little trial and error can lead to fantastic results.

2 Likes
18

I’ve had great success using Berry’s 124 grain bullets in my Glock 19. The recoil is manageable, and accuracy is spot on for both practice and defense.

19

I agree! I use these bullets in my Sig P320, and the performance is impressive. They feed well and group tightly.

20

I’ve been experimenting with different powders. So far, CFE Pistol gives a nice balance with low recoil. Anyone else find a good load?